PLUMBING FOR BEGINNERS: THE ESSENTIALS FOR INSTALLING A BATHTUB

Plumbing for Beginners: The Essentials for Installing a Bathtub

Plumbing for Beginners: The Essentials for Installing a Bathtub

Blog Article

View Website

Have you been trying to find help and advice around Installing A Bathtub?


How to Install a Bathtub Yourself
Mounting a bath tub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a moderately tough project. If the old tub is conveniently easily accessible, the task can move easily; if you have to open up a wall surface to remove the old tub and also place the new tub, the job is much harder. In either case, the job is within a home handyman's skills, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. See to it you have actually certified yourself for the job and fit trying it. Instead of hiring a professional to take control of a halfway-completed task, it is better to think about using one before you start. Possibilities are you may need a professional plumber to make tube connections.
This article will certainly assist you set up a brand-new bathtub in your restroom if you have actually currently bought a brand-new tub as well as do not need to transform the plan of your previous supply of water pipelines.
Your devices as well as product list ought to consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Removing Old Touches


    If you require to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of eliminating the existing taps can be fairly problematic due to the limited gain access to that is commonly the case.
    Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the remaining water that will come from the pipes. When the supply pipelines have actually been eliminated, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
    Before carrying on to fit the brand-new faucets, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.

    Suitable New Taps


    If the tails of the brand-new taps are plastic, after that you will need a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the existing supply pipelines.
    If you need to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
    Next, place the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines are in place in between the tap and the sink. Protect the tap in place with the maker given backnut. As soon as the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous type needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.

    Mounting the Tub


    Making use of both wooden boards under its feet, position the bathtub in the required placement. The wood boards are handy in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 little factors.
    The following objective is to ensure that the bath tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the tub till the level checks out degree.
    To install faucets, fit the bottom of the outermost adaptable tap port to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other tap.
    Turn on the water supply and inspect all joints and brand-new pipework for leaks and also tighten them if required. Load the bathtub as well as additionally examine the overflow electrical outlet and the regular outlet for leaks.
    Lastly, fix the bath paneling as explained in the supplier's user's manual. Tiling and securing around the bathtub must wait till the bath tub has been made use of a minimum of once as this will settle it right into its last position.

    Planning for the Setup


    First of all, the sustaining framework supplied with the bathroom should be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make certain that if the tap includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
    Fit the versatile faucet adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you use all of the supplied washing machines.
    Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its final position.

    Tiling Around the Bathtub


    In the area where the bathroom fulfills the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to fracture a rigid seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, bring about complications with moisture and also possible leakages to the ceiling listed below.
    You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to permit the activity experienced when the bathtub is in use. The sealer can fracture rather very early if you do not take into consideration this activity prior to securing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently offered on the marketplace. It is recommended to fit the tiles making use of waterproof or waterproof adhesive and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    I'm certainly very drawn to How to Install a Bathtub and I really hope you liked our page. Loved our blog posting? Please share it. Help someone else locate it. Kudos for your time. Don't forget to stop by our website back soon.


    Drain blockage? Seek our expertise.

    Report this page